How Telecom Towers Can Cut Energy Costs with Remote Monitoring

Telecom tower operators cut energy costs by monitoring and controlling every generator, battery and grid connection from one remote platform, so fuel waste, outages and unnecessary site visits show up in data instead of on invoices. A hardware-agnostic energy management system (EMS) does this across mixed equipment without replacing it.

For towercos running hundreds or thousands of sites, energy is one of the largest operating costs, and much of it is invisible until something fails. This article explains where tower energy cost goes, five ways remote monitoring reduces it, and what one Nigerian network found when it started measuring.

Where tower energy cost actually goes

Most tower sites run on a mix of grid power, diesel generators and batteries. The cost problems are rarely dramatic. They are quiet and repeated across many sites:

  • Unreliable grid supply. When the grid drops out, generators carry the load and fuel use climbs.
  • Generators running at the wrong load. Lightly loaded generators burn more fuel per unit of power and fail more often.
  • Fuel loss. Without per-site fuel data, theft and leaks look like normal consumption.
  • Truck rolls. Every visit to diagnose a fault or update a configuration costs travel, time and technician hours.

You cannot fix what you cannot see, and a site that is not monitored is a site where these costs go unnoticed.

5 ways remote monitoring cuts tower energy costs

  1. See fuel use per site. Live fuel levels and consumption data show which sites burn more than they should, and flag sudden drops that point to fuel theft.
  2. Fix generator load. Tracking generator performance shows units running at low load, which strains the machine and raises fuel use. Reconfiguring them to run at proper thresholds reduces failures.
  3. Lean on batteries before generators. Battery state of charge and health data show where backup batteries are underused or poorly maintained, so sites can rely less on generators for backup.
  4. Fix many sites at once, remotely. With Galooli’s X-Ray, operators batch sync a large number of sites in minutes and change configurations to optimize them, instead of sending a crew to each one. See how Active Remote Control works.
  5. Prioritize with alerts and analytics. Configurable alarms and AI-assisted analytics point crews to the sites that need attention first, so visits are fewer and better targeted.

Remote monitoring vs manual site management

Area Manual site management Galooli remote monitoring (EMS)
Site visibility Status known only after a visit or a failure Live status of generators, batteries and grid across all sites
Fuel tracking Periodic manual readings and delivery receipts Continuous fuel level and consumption data with alerts
Fixing a configuration Technician travels to each site Remote batch sync and configuration changes across many sites in minutes
Equipment brands Separate tools per vendor One hardware-agnostic view across mixed equipment
Prioritizing work Reactive, after an outage Alerts and analytics rank sites by need

What one Nigerian network found

A Nigerian telecom operator put Galooli monitoring on several hundred sites in 2021. The data showed problems that were invisible before. These are figures from Galooli’s case study:

  1. The grid was available just over 30% of the time, which forced heavy reliance on generators.
  2. Fuel use rose by almost 24% in one month, to 611,000 liters.
  3. Generators ran at 31 to 38% load, far below optimal, and around 1,900 generator failures were recorded in a month.
  4. 38% of sites had at least one extended outage in that month.
  5. The operator saved 11%, or over $500,000, in annual fuel costs from just several hundred sites.

The analysis also found that updating and properly using backup batteries could cut weekly fuel usage by more than half. Results depend on each network’s grid, equipment and site conditions, so treat these as one example, not a promise.

How to start

You do not need to replace equipment to begin. Start with a pilot group of sites with the highest fuel use or the most outages, connect the generators, batteries and meters already on site, and measure fuel use and generator load for a few weeks. The data shows where the savings are before you scale up. You can estimate your own range with the savings calculator, and see how Galooli supports the telecommunications industry. For site upkeep, see our Tower Maintenance guide.

 

 

Connect With Us

Are you ready to transform your data into
operational cost savings & efficiency?
Towers reduce energy costs by monitoring fuel, generator load, batteries and grid availability at every site, then acting on the data. The biggest savings usually come from cutting wasted fuel and avoiding unnecessary site visits.
A hardware-agnostic energy management system works with equipment from different manufacturers in one platform. Operators keep the generators, batteries and meters they already have, instead of replacing them to fit one vendor's system.
Galooli is hardware-agnostic, so it is built to work with equipment from different manufacturers in one platform. Check the integrations page or ask for a compatibility check on your specific models before you plan a rollout.
Alerts tell you which site has a problem and what kind, and remote updates fix many issues without travel. With X-Ray, operators batch sync a large number of sites in minutes and change configurations to optimize them.
It depends on the network. In a 2021 Nigerian case study, the operator saved 11%, or over $500,000, in annual fuel costs from several hundred sites. Your result depends on grid reliability, generator load and fuel practices.

 

Recommended Posts